MTX-MRX Editor V3.2.0 for Win10 / 8.1 / 7 and firmware V3.20-2 (Previous version)

• To update the firmware, please refer to the MTX/MRX system Firmware Update Guide.
• When the firmware of the device will update without compatibility version of editor, ensure that the MTX/MRX system is synchronized and saved to MTX-MRX Editor as a project file before performing the firmware update in order to ensure that your project data is not lost, and then perform the firmware upgrade using the latest version of MTX-MRX Editor. Ensure that the device is initialized after the update, and then open the previously saved project file using the latest MTX-MRX Editor and re-synchronize to the updated devices.
• When initializing Dante devices (MTX5-D, MRX7-D, PGM1 and Dante model of XMV), ensure that all other Dante devices on the network are disconnected or powered off. Otherwise initialization could take longer than necessary.
• To prevent damage to the SD memory card as well as loss of data, do not remove or insert the SD memory card while the device is on.
• Although MTX-MRX Editor shows 'Completed' after updating firmware, do not turn off the power of the device until the indicators on the front panel have stopped blinking.
• In the unlikely case of hardware failure, initialize the replacement device(s), confirm proper ID and DIP switch settings, and then resynchronize from MTX-MRX Editor to the device(s).
• When entering text into a text field inside a dialog box of MTX-MRX Editor using Input Method Editors, such as Microsoft IME, ensure that the mouse pointer is not clicked over another area of the open dialog window before converting and applying the text. This will cause the keyboard input to stop. Should this happen, close and re-open the dialog box.
• Do not enter the following characters in text fields in the MTX-MRX Editor.
  & < > “ ‘ / $’ \n (line feed) \t (tab)
  These characters may disappear or change into unexpected characters.
• When the project file created by MTX Editor V1.0x is opened with MTX-MRX Editor or MTX Editor V1.1x or later, [Play] selected by "SD Song Select & Play" in the “Preset” dialog, is changed to [No Assign]. In this case, manually change [No Assign] for all necessary Presets to [Play].
• Do not use the EEE function (*) of network switches in a Dante network. Although power management should be negotiated automatically in switches that support EEE, some switches do not perform the negotiation properly. This may cause EEE to be enabled in Dante networks when it is not appropriate, resulting in poor synchronization performance and occasional dropouts. Therefore we strongly recommend that:
  
  1. If you use managed switches, ensure that they allow EEE to be disabled. Make sure that EEE is disabled on all ports used for real-time Dante traffic.
  2. If you use unmanaged switches, make sure to not use network switches that support the EEE function, since EEE operation cannot be disabled in these switches.
  *EEE (Energy Efficient Ethernet) is a technology that reduces switch power consumption during periods of low network traffic. It is also known as Green Ethernet and IEEE802.3az.
• When the MTX-MRX Editor changes Dante patch settings for large numbers of devices, it may take several minutes after synchronization is shown to be complete (in MTX-MRX Editor) for the patch to be established and audio to be heard.

This zip file includes the following software

MTX-MRX Editor / Firmware / Wireless DCP / ProVisionaire Touch / Tio1608-D / R Series (Rio/Ri/Ro) Compatibilities (Win)

Please make sure to use the appropriate versions of firmware and software, referring to the following compatibility charts. Using an unsupported combination may result in malfunction.

Compatibility List

MTX-MRX Editor V3.2.0

New Functions

• Now supports control for Rio3224-D, Rio1608-D, Ri8-D, Ro8-D and Tio1608-D.
  Please perform the patch to the above-mentioned model from MTX5-D or MRX7-D with the Dante Controller.
  When included in an MTX/MRX system, the R series (AD/DA) and Tio1608-D are the target of a preset recall. The parameters which are recallable are +48V, HPF, and HA gain.
• Added the Audio Detector component and the Summer component to MRX7-D.
• MTX-MRX Editor has been enabled to control the devices belonging to a different subnet. However, please keep in mind the following points:
  • One system is arranged in the same subnet.
  • Preset Link does not function between the systems for different subnets.
• Added Matrix Out Level to the MTX3 and MTX5-D. As a result, the fader at the lower right of the "MATRIX" screen was changed to Matrix Out Level from Zone Out Level. Moreover, the Matrix Out Level can be controlled now from external controllers, such as DCP and GPI.
• Now supports AES67 mode and Device Lock of Dante.

Enhancement

• Some screens and component editors are now compatible with high-resolution monitors.

Fixed Bugs

• Fixed a problem in which, from the "Digital Control Panel" dialog, if you selected [Legacy - MTX Source Select (w/sw)] or [Legacy - MTX Source Select (w/knob)], the display of [Upper Limit] would show [-∞] (infinity).
• Fixed a problem in which if you deleted a device by “Device Configuration Wizard,” an editor and preset recall change of a parameter may not actually change the parameter in the device.

MRX7-D V3.20

New Functions

• Added the Audio Detector component and the Summer component.
• Now supports AES 67 mode and Device Lock of Dante.
• Now supports control for Rio3224-D, Rio1608-D, Ri8-D, Ro8-D and Tio1608-D.
  Please perform the patch to the above-mentioned model from MRX7-D with the Dante Controller.

Fixed Bug

• Fixed a problem when different large settings for every channel for the Delay value of the "Delay Matrix" component, 07 alerts may occur on occasion and the audio may stop. The amount of the DSP resources used for the "Delay Matrix" component has been increased by this bug fix.

MTX5-D V3.20

New Functions

• Added the Matrix Out Level.
• Now supports AES67 mode and Device Lock of Dante.
• Now supports control for Rio3224-D, Rio1608-D, Ri8-D, Ro8-D and Tio1608-D.
  Please perform the patch to the above-mentioned model from MTX5-D with the Dante Controller.

MTX3 V3.20

New Functions

• Added the Matrix Out Level.
• Now supports control for Rio3224-D, Rio1608-D, Ri8-D, Ro8-D and Tio1608-D.

XMV V3.20

New Function

• Now supports AES67 mode and Device Lock of Dante.

Exi8 V3.20 / EXo8 V3.20 / MCP1 V3.20 / PGM1/PGX1 V3.20

• No change in this version; however, the firmware version number is updated to match other devices.

Known issues

• In the "Dante Information" dialog of MTX-MRX Editor, "Dante (A) FW" is displayed as 3.10.5.50987013 instead of 3.10.5.1. Confirm the correct version number on the Dante Controller.
• If the Device Latency was set to 2 msec or 5 msec by the Dante Controller, the MTX-MRX Editor would display the setting as 1 msec. Confirm the correct latency value on the Dante Controller.

NOTICE

• In the Dante model, Dante Device Labels can be changed arbitrarily and permanently. These changes can be made from the Dante Controller software.
  However, since the five initial characters are used for device identification (decided by UNIT ID), they should not be changed. The 6th character and subsequent ones can be changed arbitrarily.
  Moreover, the following rules concerning Dante Device Labels are common to all Dante devices (and not just this one):
  • Conventional characters (alphabetical uppercase or lowercase), numerals, or hyphens (-) can be used.
  • A maximum of 31 characters can be entered.
• When you change the frequency of a clock source supplied externally, also make sure to change the Dante word clock setting using MTX-MRX Editor or Dante Controller.
  When you change a setting by MTX-MRX Editor, choose System Word Clock Fs appropriately in the "Word Clock" dialog box of MTX-MRX Editor, and synchronize by "To Device."
  When you change a setting by Dante Controller, please refer to the help function or user's guide of Dante Controller.
  Keep in mind that the entire system may be affected by the settings in a single part. Major problems can occur when a device not intended to be a part of the system is set to a word clock setting that the other Dante devices do not support.
• When using the AES67 mode and/or Device Lock of Dante, we recommend that you checkmark the [Preserve the settings of Dante Controller] check box in the MTX-MRX Editor.
• When Tio1608-D is included in an MTX/MRX system, Tio1608-D cannot carry out concurrent connection of CL, QL, TF, and MTX-MRX Editor.
  Moreover, when Tio1608-D and/or R series (AD/DA) are included in an MTX/MRX system, MTX-MRX Editor and R-Remote cannot carry out concurrent connection.